Highest Quality Motor On The Market In
North & South America....
NOW with a 42mm Tube To Fit The
Winegard DS2076 Satellite Dish Antenna, & Many Other Popular Dishes
Works In Northern & Southern Hemisphere
HEAVY DUTY METAL GEAR Inside
Motorize Your Winegard Satellite Dish Now With a POWERMAX SG9120B
Steel Gears Make This DiSEqC Motor Truly Heavy Duty.
Spend Money On Older Models
Claiming To Be Heavy Duty with Plastic Gear. The SG9120B Is The
Latest & Most Durable & Heavy Duty DiSEqC Motor On The Market!
Need to adjust your SG9120 or
SG9120B for backlash? Download
Follow these instructions
|Note: Please DO NOT use a wrench to
tighten your "F" fittings. This will damage the
connector on the motor and is not covered under warranty.
Superior Design & Stable
Mounting System For Dishes As Large As 120cm (4ft)
SG9120 Fits dishes up to 1.2m
SG9120B Fits Winegard DS2076
Smart-Fit design allows back bracket to mount snug.
Specially designed back bracket for use of motor in
both Northern and Southern Hemisphere (Example: North America &
Larger oversized mounting bracket helps with wind resistance
1-year manufacturers warranty
DiSEqC 1.2 Compatible
Everything controlled via
1 coaxial cable
Ultra low noise
Goto X function
LED Power Indicator
East/West movement button
Degree indicator on shaft
Hardware Reset button to
to allow you to easily reset the motor with a quick touch of a
Do I need to install a separate power
line to connect to the automatic
HH dish motor mount?
motor gets powered by the receiver. The receiver provides power to turn
the LNB on and to switch polarity. The motor consumes the same power
through the coaxial cable that runs from
the receiver to the LNBF. Simply run the coaxial cable to your
satellite dish motor, then from the HH dish motor
run a 3 or 4 foot coaxial cable to the LNBF.
How do I control the motor to move it East /
The motor is
controlled by the receiver's remote control. All receivers compliant
with the DiSEqC 1.2, 1.3, or USALS protocol have the capability to run
an HH satellite motor. Once you install
and setup the motor to follow the satellite arch properly and store the
different satellite positions and locations into the receiver, the
receiver will automatically go to the location where the channel is
being broadcasted from when you change TV channels on the receiver.
Are all HH motors & receivers
1.2, & DiSEqC 1.3 compatible?
satellite motors and HH mounts are DiSEqC1.2 & DiSEqC1.3 compatible, but
not all dish motors are USALS compatible.
Motors that are NOT USALS compatible are sometimes more reliable.
satellite C/Ku band receivers are DiSEqC 1.2 and DiSEqC 1.3 compatible.
Some are DiSEqC1.0. Make sure the receiver
you purchase is at least DiSEqC 1.2 compatible.
Can I pick up C band and Ku band?
need a C band dish (2.4 meters / 6 foot) or larger to be able to pick up
C band. This system is only for Ku band reception.
Does the motor also adjust for variation in
elevation on the dish for each and every satellite
you install the motor based on your latitude, the motor will adjust the
elevation as well.
Should I skew (rotate) my LNBF to align for
leave the LNB at 0 degrees skew and the motor will tilt the satellite
dish to make up for the adjustment of skew.
What is the benefit from motorizing my dish?
motor to your system allows you to receive satellite channels from
multiple satellites & not just one.
Do I need to manually
turn the dish every time I change channels?
No. This is an automatic satellite dish motor.
Once it's installed properly and your receiver is
programmed with the locations of the satellites,
every time you change channels, the receiver sends
DiSEqC commands to the satellite motor to tell it to
move and stop at a certain location where the
satellite signal is broadcasting from.
How do I wire up the
SG-9120 Dish Motor?
Simply run the coaxial cable to your satellite dish
motor, then from the HH dish
motor run a 3 or 4 foot coaxial cable to the